Home / MTK ALL / Huawei Y520-U22 MTK6572 100% tested scatter file

Huawei Y520-U22 MTK6572 100% tested scatter file

Huawei Ascend Y520-U22 Overview

Huawei released an amazing smart phone which names Huawei Ascend Y520-U22. This smart phone is with a power full 1.3Ghz Dual Core Processor. Huawei Ascend Y520-U22 Camera is 5 MP back camera, VGA front camera and Flash light. Huawei Ascend Y520-U22 display size is 4.5 inches and 480×854 pixels. Huawei Ascend Y520-U22 Memory is with 512 MB RAM, 4 GB internal Memory and up to 32 GB external SD card support. Other features are Bluetooth, WLAN, GPS, GPRS, FM Radio, Dual SIM stand by and etc.

Huawei Ascend Y520-U22 Specification

General

Android Jelly Bean 4.4
Dual Sim stand by
3G and 2G

Processor

1.3Ghz Dual Core

Memory

512 MB RAM
4Gb internal memory
21 Gb external SD card support

Camera

5 MP back camera
VGA front camera
Flash light

Display

5.0 inches 480×854 pixels

Browser

HTML

Connectivity

Bluetooth
WLAN
GPS
GPRS

Messeging

SMS
MMS
EMails
Push Mails

Battery

1730mAh

Operating System
Android Jelly Bean 4.4

How to Flash Y520-U22 With Spflash tool?

The requirements of Y520-U22 is battery backup of 40% to 50%.

  1. Download and install Y520-U22 Usb Drivers.
  2. Download Stock Rom of Y520-U22 Firmware Password is huawei4
  3. Power Off your Mobile and remove Battery.
  4. Download and extract spflash tool.
  5. Now open sp flash tool and specify scatter file from that stock rom.
  6. Now press download button. if face any error change download mode to firmware upgrade.
  7. when Green bar of Ok appears your flashing done.
  8. Now unplug cable and remove battery.
  9. Now insert battery and press power button.
  10. Your flashing is complete enjoy.
  11. if you faced any error copy and paste that error in comments.

Huawei Y520-U22 Dead After Flash Sp flash tool 4032 Error Solution

 

 

About admin

Check Also

Lenovo A7000A Plus S308 MTK6572 100% tested scatter file

There are many problems which when occurred in Lenovo A7000A Plus, we need to flash …

35 comments

  1. %HANXXXXXXXXXXXXXXX

  2. thanks broo

  3. admin good day, when execute the flash all was ok but when in the flashing process it has no progress 0% and then pop up message box appear says BROM ERROR : S_DA_SDMMC_WRITE_FAILED (3149)

  4. Please i need answers just reply on my e mail provided, thank you

  5. sir after flash my phone dislay is wite and turn of

  6. BROM ERROR : S_FT_ENABLE_DRAM_FAIL (0xFC0)

    what is solution for this error

  7. admin good day, when execute the flash all was ok but when in the flashing process it has no progress 0% and then pop up message box appear says BROM ERROR : S_DA_SDMMC_WRITE_FAILED

  8. thanks for flash file it works 100%

  9. Dear Admin, Please help following sentence are what i see in my huawei screen :

    Android system recovery
    Y520-u22v100r001c567b108

    reboot / apply update / wipe data / backup / restore / root check

    all above options dose not work

    What can i do ?

  10. Sir mera mobile bar bar disconnect ho jata ha ….Please help me

    • Try to flash it with out battery if facing issue again then Issue is with charging base, Charging Cable or computer port. Replace these one by one then try.

  11. gadgedandroid.com

    Thanks For Sharing Bro

  12. blank screen white …please help me

  13. thanks brooooooooooo

  14. Its all ok when i flashed my but…..but when i open my phone nothing happen after flashing its remain same problem…….the problem not fix

  15. pls….help me

  16. thanks it works fine for me

  17. mera cell blank ho gaya hai is file se flash k baad what should i do

  18. am lode the file.but the downloading not start.its always 0%

  19. When i try to flash with SP Flash Tool , i had this error message : s_brom_cmd_startcmd_fail (0x7D5) ,
    please help me

  20. Admin, Sir perfectly flashed without any error message pop on screen, but when i try to put the battery and switch on, the phone can’t boot up. only Huawei logo icon is there… please help.

    Thank you.

  21. After successful flash My phone display became white. Whats the problem? How to solve it?

  22. ERROR S_FT_ENABLE_DRAM_FAIL {4032} PLEASE SOLUTION

  23. PMT changed for the ROM; it must be downloaded

  24. This firmware works for Y520-u03?

  25. this firmware will kill the phone error

Leave a Reply

Your email address will not be published. Required fields are marked *

Time limit is exhausted. Please reload CAPTCHA.